Greaseweazle v4.1 Amiga Amstrad, Spectrum

Greaseweazle V4.1 USB Floppy Adapter Flux Reader Writer

Name: Greaseweazle V4.1 USB Floppy Adapter Flux Reader Writer
SKU: GW-V4
Availability: OutOfStock

£20.83 Ex. VAT

Greaseweazle v4.1 allows versatile floppy drive control over USB. By extracting the raw flux transitions from a drive, any disk format can be captured and analysed – PC, Amiga, Amstrad, PDP-11, musical instruments, industrial equipment, and more. The Greaseweazle also supports writing to floppy disks, from a range of image file formats including those commonly used for online preservation (ADF, IPF, DSK, IMG, HFE)

Greaseweazle V4.1 is the latest version, updated for mass production and with the following features:

Reads and writes 3″, 3.5″, 5.25″, 8″ disks (with suitable drive and cable)
Buffered outputs, for communicating with older 5.25″ and 8″ disk drives
Integrated power connector for directly powering most 3.5″ disk drives
Write-enable jumper can be removed for safer preservation of precious vintage disks
Supports flippy-modded 5.25″ drives
Supports Disk-Change detection as used by Rob Smith’s integration into the WinUAE Amiga emulator
3 user-definable outputs (eg. 8″ interface REDWC signal)
100% factory tested, and tested again by me before shipping

More information and documentation on the wiki page here:

This listing is for the Greaseweazle V4.1 device only. And does not include which you will require:

A disk drive (for example a PC 3.5″ or 5.25″ drive)
A floppy ribbon cable (typically you want a standard PC cable with ‘twist’ on pins 10-16, to communicate with a PC floppy drive)
Floppy drive power cable, or power supply

Built by Zero Flux Development.

And yes this is the item mentioned on Tom’s Hardware: https://www.tomshardware.com/news/raspberry-pi-emulates-amiga-1200-uses-real-floppy-disks

OUT OF STOCK

SKU: GW-V4 Categories: A1200 Upgrades, A2000 Upgrades, A4000 Upgrades, A500 Plus Upgrades, A500 Upgrades, A600 Upgrades, ZX Spectrum Upgrades Tags: Amiga, amstrad, atari, Gotek, Greaseweazle, spectrum

You may also like…

TF1230 Accelerator Amiga 1200 - Terriblefire

TF1230 Amiga Accelerator 128Mb – Terriblefire

TF1230 Amiga Accelerator - Terriblefire for the Amiga 1200 which hosts a 68030 processor running at 50Mhz coupled with 128mb of fast ram. This card is a perfect add-on for the Amiga A1200 and is the sweet spot between cost and speed.This card is a perfect add-on for the Amiga A1200 and is the sweet spot between cost and speed. And is the next step up after the 11Mb Ex1T Fast Ram or if your budget does not quite stretch to the Terriblefire TF1260, the TF1230 A1200 card is the perfect add-on and you will notice a huge speed difference.

68030 'Gold' CPU running at 50MHZ (NOT OVERCLOCKED) with MMU
128Mb Fast Ram
IDE Interface - Driver required - ehide.device or purchase our AmigaOS 3.2 Rom with ehide.device built in (uploading of AmigaOS purchase evidence required)
Fits in your old/new stock A1200 case!!!

Prerequisites

Timing fix is strongly recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
Kickstart ROM 3.1, 3.1.4, 3.2, 3.x or 3.9 (not compatible with 3.0).
Some boards do not have a chamfered edge on the connector (1A and 1B boards) which may bend the connector pins, if your unsure please ask.

What is TerribleFire?

Well it's not what it's who, and that person is Stephen Leary who has designed a whole host of accelerators and ram cards for the Amiga A500, A1200 and Amiga CD32. These include many but the most common ones are:

TF328 - 8Mb Fast Ram board and IDE socket for the Amiga CD32
TF330 - 68030 Processor, 64Mb Fast Ram and IDE socket for the Amiga CD32
TF534 - 68030 Processor, 4Mb Ram, IDE Interface and FPU Socket for A500/A500 Plus and A2000
TF536 - 68030 Processor, 64Mb Ram and IDE interface for the Amiga A500 and A500 Plus
TF360 - 68060 Processor other specs TBC for the Amiga CD32
TF1260 - 68060 Processor, 128Mb Ram and IDE Interface for the Amiga 1200
TF1230 - 68030 Processor 64Mb Ram amd IDE interface for the Amiga 1200
TF4060 - 68060 Processot 128Mb Ram for the Amiga 4000
TF1200 - Buffee Adaptor + 5.5Mb/8Mb (you will need the new Buffee Processor

£158.33 Ex. VAT Read more

PiStorm32 Lite A1200 with RPi 3A+, 64Gb SD Card

PiStorm32-Lite A1200 is the full package which includes:

PiStorm32-Lite A1200 Adaptor
Raspberry Pi 3A+ Module
64Gb SD Card (Pre-installed kernel with EMU68) You will need a copy of Workbench 3.0 or above and a kickstart rom again 3.1 or above or send us an SD image and we will install and setup FOC.
3D printed RPi header protector

Once installed and setup you will have an implementation of MC68020/030/040 with FPU support, coupled with a fast implementation of the Emu68 CPU unit (Emu68 is a JIT emulator) written by Michal Schulz, thanks to it the system boots in a few seconds. Extra functionality is added (thanks to an additional RPi 3A+ module) with an HDMI port, so you can have Full HD video and around 340MB of Fast Ram. Check out this video by Capt. LeChuck, Pistorm32-Lite with EMU68K [kad_youtube url="https://www.youtube.com/watch?v=8BBU48cLuUc&t=109s" ] We also just sell the Pistorm32-Lite adaptor here, just add you own Raspberry Pi and SD Card.

NOTE: This is a open source project and will require some knowledge of the Amiga. The PiStorm adaptors are professionally manufactured, and a contribution to the developer is made.

£124.99 Ex. VAT Select options

Refurbished Commodore Amiga 1200 Unit

Commodore Amiga 1200 - Professionally refurbished

Technical Specifications

Motorola 68020 (14Mhz) CPU
2Mb Chip Ram
3.0 Kickstart Roms
3.5" Floppy Drive
UK Layout Keyboard

What's included?

Professionally refurbished Amiga 1200 Unit (excluding mouse and PSU, these are options that can be added below).

What is refurbished? Each Commodore Amiga 1200 mainboard is professionally recapped (standard or Polymer is available at extra cost) and deep cleaned using a Ultrasonic cleaner, bathed using deionised water and professional grade PCB/Flux cleaning solution. Once completed it is dried and a full diagnostic test is completed. Each unit is thoroughly inspected make sure the Amiga 1200 worked as it did when it first came from the factory back in the 1990’s, case and keyboard is stripped and cleaned but due to age may show signs of use. Each Amiga 1200 is refurbished to the customers specifications, with that in mind each unit can take 14/21 working days to prepare and test depending on demand. What is Ultrasonic cleaning? Ultrasonic cleaning is a process that uses ultrasound (usually from 20–40 kHz) to agitate a fluid, this fluid is made up for this specific job which is to clean and remove any flux left over from recapping. We use deionised water (deionized depending where your from) and professional grade PCB cleaner. An example of the results and the process: [kad_youtube url="https://youtu.be/m4mbKPySfLE" ]

Want to add some extras? We want you to have the Amiga you always wanted, and that's why we can offer some great upgrades to your Amiga, for example: Extra fast ram for WHDLoad, Scan doublers, Gotek drives etc. Ordering We only ask for a deposit and the rest upon completion. Shipping now July 2024 Shipping Worldwide shipping available simply contact us for a shipping quote. Important Notes:

Images of the Amiga 1200 are for illustrative purposes only, each unit will show signs of age and use. If you want photos of the Amiga 1200 we have please contact us.
As these are custom built they can take between 21/28 working days depending on what add-ons are added and workload.
Deposits are not refundable
No software warranty or support is provided, any software included is sold as seen.

£499.99 Ex. VAT Select options

Commodore Amiga PSU for A1200

Commodore Amiga PSU for A1200, these are brand new and modern with It's 50W (55W peak) of total combined output power making it nearly 2x times stronger than original Commodore Amiga PSU and 2x smaller in dimensions & weight.

Key features:

Stabilized & filtered 5VDC up to 4A output (4.4A peak)
Stabilized & filtered 12VDC up to 2A output (2.2A peak)
Stabilized & filtered -12VDC up to 0.5A output (0.55A peak)
Carefully calibrated for Amiga 500 reference load
Active & passive over voltage protection for main +5VDC line
Over current protection for all output lines
Fully isolated & fused on AC side
Power On/Off switch
Long output cable (1.8m) with rectangular DIN 5-pin plug.
Detachable input AC cable for all versions (cable included)
Weight only 0.4 KG (2x less than original PSU)
Runs COLD!
Safety standards: UL60950-1, TUV EN60950-1, ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1
Manufactured by Electroware
UK Stock

Warning! Risk of electrical shock and energy hazard when opened. All failures should be examined by a qualified technicians only. Risk of fire or electrical shock. The ventilation holes should be protected from foreign objects or dripping liquids. Please do not install power supplies in places with high ambient temperature or close to the heat source. Enclosed power supplies are intent to work in indoor locations, it's not allowed to use power supplies outdoor, in dust or high moisture. Output current and output wattage must not exceed the rated values. This replacement Amiga PSU has been designed for Commodore Amiga 1200 vintage computer systems only and should be considered as an integral component of Amiga computer system. Do not connect to any other devices as it's not a general purpose PSU. Manufacturer is not responsible for any consequences of unauthorised or arbitrary repairs, modifications or incorrect usage. Please notice that new, properly working replacement Amiga PSU is reducing the system's potential fail rate but still is not guaranteeing that entire Amiga system will work correctly (it's >30 years old).

£45.83 Ex. VAT Read more

TF1260 TerribleFire A1200 Accelerator with LC060 50MHz CPU

TF1260 Terriblefire A1200 Accelerator with EC 50Mhz CPU which hosts 128Mb Fast Ram, IDE connector. The TF1260 is one of the best 060 accelerators you can purchase for the Amiga 1200 And is the next step up after the TF1230 A1200 Accelerator add-on we sell for those that want that large speed jump. Full specs:

MC68LC060 CPU (The CPU has no MMU or FPU)
128MByte of fast-ram.
IDE Interface - Driver required - ehide.device
Compatible with any A1200 motherboard revision.
Fits in your old/new stock A1200 case!!!

What is Terriblefire? Well it's not what it's who, and that person is Stephen Leary who has designed a whole host of accelerators and ram cards for the Amiga A500, A1200 and Amiga CD32. These include many but the most common ones are:

TF328 - 8Mb Fast Ram board and IDE socket for the Amiga CD32
TF330 - 68030 Processor, 64Mb Fast Ram and IDE socket for the Amiga CD32
TF536 - 68030 Processor, 64Mb Ram and IDE interface for the Amiga A500 and A500 Plus
TF360 - 68060 Processor other specs TBC for the Amiga CD32
TF1260 - 68060 Processor, 128Mb Ram and IDE Interface for the Amiga 1200
TF1230 - 68030 Processor 64Mb Ram and IDE interface for the Amiga 1200
TF4060 - 68060 Processor 128Mb Ram for the Amiga 4000
TF1200 - Buffee Adaptor + 5.5Mb/8Mb (you will need the new Buffee Processor

NOTES:

For every TF1260 sold we donate a percentage of the sale to Stephen Leary to support further TF card developments and we also support our builders.
Timing fix is recommended on your A1200 motherboard. We can do this free of charge if you send your board to us (return shipping does need to be covered).
At least Kickstart 3.1 is required - (Kickstart 3.0 is not supported)

£249.99 Ex. VAT Select options

PiStorm32 Lite for Amiga A1200 Adaptor Only

PiStorm32 Lite Adaptor for the Amiga A1200 is designed to connect one of the Raspberry Pi's listed below (not included) NOTE: We do sell a plug and play package here which includes PiStorm32-Lite, Raspberry Pi 3A & SD Card. Once you add your own Raspberry Pi, setup an SD card and plug it in the trapdoor of the A1200 like all A1200 accelerators (TF1230 or TF1260) you will have an accelerated Amiga 1200! Compatible Rasperry Pi's:

Raspberry Pi 3A
Raspbery Pi 3B
Raspberry Pi 4B

Want to know more about the PiStorm check out the following link: https://github.com/PiStorm/pistorm32-lite-hardware Compatible Rasperry Pi's:

Raspberry Pi 3A
Raspbery Pi 3B
Raspberry Pi 4B

With the Pistorm32-lite the A1200 can go up to a 68040 and using a Pi4 you could see 2000 Plus Mips! Want to know more about the PiStorm check out the following link: https://github.com/PiStorm/pistorm32-lite-hardware The PiStorm adaptors are professionally manufactured. and a contribution to the developer is made to support this project.

£70.83 Ex. VAT Read more

Amiga A1200 Recapping Service (PREMIUM)

Amiga A1200 recapping service (Premium) using hybrid polymer capacitors (never leak again!), all board revisions (1A,1B,1D1,1D4,2B). NOTE this is NOT a repair service.

Check of the board before recapping is begun (any faults found before recapping will be reported back)
Removal of existing capacitors (both SMD and radial capacitors).
Cleanup and preparation of area.
Replace using either polymer Panasonic/Wurth/KEMET capacitors.
Retest (Video, Audio, Floppy Boot, CF Card boot).

Want to know more about recapping, check out our FAQ's

Overseas recapping orders

Overseas orders are very welcome and we are able to provide you return shipping costs at the checkout. To do this add any of our recapping services to your shopping basket and then at the checkout simply fill in the billing and shipping form including your telephone and email address (important) and click the 'Request a quote' link. You will receive an email within 24hrs with the shipping cost and you can then proceed with the order by clicking on the 'Complete your order' within the email. There is no need to leave the checkout page open your web browser.

£45.83 Ex. VAT Select options

Amiga A1200 Motherboard – Refurbished

Amiga A1200 motherboard fully refurbished (various motherboard revisions). Each A1200 motherboard is professionally refurbished and has had the following work completed:

Tested before any work has began.
All electrolytic capacitors removed using professional tools and techniques (no twisting off caps and boards a pre-warmed before the removing capacitors using hot air) this puts far less stress to the board itself.
Pads cleaned with flux/wick/IPA.
New electrolytic capacitors installed using our premium polymer capacitors.
Modulator removed.
Timing fix applied for ACA , TF1230, TF1260 Accelerator Cards.
Board retested - Video (composite and RGB), Audio, CIA, Floppy, IDE, Parallel, Serial, Mouse, Joystick, DF1.
Board ultrasonic cleaned at 60 degrees using deionised water and professional PCB flux cleaner and then dried.
Board tested again and tested for a minimum of 4 hrs playing a rolling demo.

What is Ultrasonic cleaning? Ultrasonic cleaning is a process that uses ultrasound (usually from 20–40 kHz) to agitate a fluid, this fluid is made up for this specific job which is to clean and remove any flux left over from recapping. We use deionised water (deionized depending where your from) and professional grade PCB cleaner. An example of the results and the process: https://youtu.be/m4mbKPySfLE [caption id="attachment_17767" align="aligncenter" width="300"]

Amiga Motherboard Before being Recapped & Ultrasonic Cleaned[/caption] [caption id="attachment_17766" align="aligncenter" width="300"]

Refurbished Amiga Motherboard - Recapped & Ultrasonic Cleaned[/caption] Worldwide shipping available simply contact us for a shipping quote.

Images of the Amiga 1200 motherboard is for illustrative purposes only and are PAL, each unit will show signs of age and use. If you want photos of the Amiga 1200 motherboards we have please contact us.

£379.99 Ex. VAT Select options

Greaseweazle V4.1 USB Floppy Adapter Flux Reader Writer